Rapid microwave assisted hydration of internal arylalkynes in the presence of PTSA: an efficient regioselective access to carbonyl compounds

A metal-free procedure for the regioselective hydration of internal arylalkynes under microwave irradiation is described. The reaction promoted by PTSA takes place rapidly in EtOH and regioselectively afforded in good yields various carbonyl compounds 2.     

Ultrasonic degradation of oxalic acid in aqueous solutions

This paper describes the ultrasonic degradation of oxalic acid. The effects of ultrasonic power, H₂O₂, NaCl, external gases on the degradation of oxalic acid were investigated. Reactor flask containing oxalic acid was immersed in the ultrasonic bath with water as the coupling fluid. Representative samples withdrawn were analysed by volumetric titration. Degradation degree of oxalic acid increased with increasing ultrasonic power. It was observed that H₂O₂ has negative contribution on the degradation of oxalic acid and there was an optimum concentration of NaCl for enhancing the degradation degree of oxalic acid. Although bubbling nitrogen gave higher degradation than that for bubbling air, both gases (for 20 min before sonication and during sonication together) could not help to enhance the degradation of oxalic acid when compared with the degradation without gas passage.     

Performance evaluation of traveling wave ultrasonic motor based on a model with visco-elastic friction layer on stator

A new visco-elastic contact model of traveling wave ultrasonic motor (TWUSM) is proposed. In this model, the rotor is assumed to be rigid body and the friction material on stator teeth surface to be visco-elastic body. Both load characteristics of TWUSM, such as rotation speed, torque and efficiency, and effects of interface parameters between stator and rotor on output characteristic of TWUSM can be calculated and simulated numerically by using MATLAB method based on this model. This model is compared with that one of compliant slider and rigid stator. The results show that this model can obtain bigger stall torque. The simulated results are compared with test results, and found that their load characteristics have good agreement.     

Ultrasonic polar scans: numerical simulation on generally anisotropic media

Ultrasonic polar scans are based on the recording of the reflected or transmitted amplitude of sound, impinging a fiber reinforced composite from every possible angle of incidence. The mechanical anisotropy of such materials makes the reflection coefficient direction dependent, whence an ultrasonic polar scan forms a fingerprint of the investigated material. Such scans have already proved to be very valuable in the characterization of composites. Simulations have been performed for single layered and multi-layered systems, for pulsed and harmonic waves. Fiber reinforced composites are mostly orthotropic. The current report presents simulations not only on orthotropic materials but on materials of any kind of anisotropy. These extended numerical simulations are not only valuable in the characterization of highly sophisticated composites, but may also be used to characterize thin slices of crystals and even layered crystals.     

Effect of sparse basis selection on ultrasonic signal representation

Recently, adaptive sparse representations of ultrasonic signals have been utilized to improve the performance of scanning acoustic microscopy (SAM), a common nondestructive tool for failure analysis of microelectronic packages. The adaptive sparse representation of an ultrasonic signal is generated by decomposing it in a learned overcomplete dictionary using a sparse basis selection algorithm. Detection and location of ultrasonic echoes are then performed on the basis of the resulting redundant representation. This paper investigates the effect of sparse basis selection algorithms on ultrasonic signal representation. The overcomplete independent component analysis, focal underdetermined system solver (FOCUSS), and sparse Bayesian learning algorithms are examined. Numerical simulations are performed to quantitatively analyze the efficiency of ultrasonic signal representations. Experiments with ultrasonic A-scans acquired from flip-chip packages are also carried out in the study. The efficiency of ultrasonic signal representations are evaluated in terms of the different criteria that can be used to measure its performance for different SAM applications, such as waveform estimation, echo detection, echo location and C-scan imaging. The results show that the FOCUSS algorithm performs best overall.     

Sonocatalytic degradation of acid red B and rhodamine B catalyzed by nano-sized ZnO powder under ultrasonic irradiation

Nano-sized ZnO powder was introduced to act as the sonocatalyst after the treatment of high-temperature activation, and the ultrasound of low power was used as an irradiation source to induce nano-sized ZnO powder performing sonocatalytic degradation of acid red B and rhodamine B. At the same time, the effects of operational parameters such as solution pH value, initial concentration of dyestuff and addition amount of nano-sized ZnO powder have been examined in this paper. We found that the degradation ratios of acid red B and rhodamine B in the presence of nano-sized ZnO powder were much higher than that with only ultrasonic irradiation. However, the degradation ratio of acid red B was about two times higher than that of rhodamine B for the initial concentration of 10.0 mg/L, addition amount of 1.0 g/L nano-sized ZnO powder, solution acidity of pH 7.0 and 60 min irradiation experimental condition. The difference of the degradation ratios can be illustrated by the difference of chemical forms of acid red B and rhodamine B in aqueous solution and the surface properties of nano-sized ZnO particles. In addition, the researches on the kinetics of sonocatalytic reactions of acid red B and rhodamine B have also been performed and found to the follow pseudo first-order kinetics. All the experiments indicated that the sonocatalytic method in the presence of nano-sized ZnO powder was an advisable choice for the treatments of non- or low-transparent organic wastewaters in future.     

Optimization and comparison of ultrasound/microwave assisted extraction (UMAE) and ultrasonic assisted extraction (UAE) of lycopene from tomatoes

The extracting technology including ultrasonic and microwave assisted extraction (UMAE) and ultrasonic assisted extraction (UAE) of lycopene from tomato paste were optimized and compared. The results showed that the optimal conditions for UMAE were 98 W microwave power together with 40 KHz ultrasonic processing, the ratio of solvents to tomato paste was 10.6:1 (V/W) and the extracting time should be 367 s; as for UAE, the extracting temperature was 86.4 °C, the ratio of the solvents to tomato paste was 8.0:1 (V/W) and the extracting time should be 29.1 min, while the percentage of lycopene yield was 97.4% and 89.4% for UMAE and UAE, respectively. These results implied that UMAE was far more efficient extracting method than UAE.     

光电沉积Co-Pi对Ta3N5水分解性能的影响及机理

Co-Pi是一种低廉高效的氧化水产氧助催化剂,助催化剂担载方法及条件是光阳极太阳能水分解效率提升的关键因素之一。以光阳极材料Ta_3N_5为基底,针对光电沉积担载助催化剂Co-Pi开展了一系列研究,研究表明光电沉积Co-Pi过程中,照射光强的影响较小,而外加偏压和担载电量的影响很大,是Co-Pi担载的关键因素;通过阻抗谱测试定量分析了Co-Pi担载条件对Ta_3N_5/电解液界面载流子输运的影响,表明Co-Pi担载电压和电量直接影响界面光生载流子的传输,进而决定了Ta_3N_5水分解性能的高低;发现最优担载偏压对不同的Ta_3N_5均适用,而最优担载电量和光阳极的表面粗糙度存在正相关关系,要针对光阳极表面粗糙度调节助催化剂担载条件。     

Mechanically Induced Catalytic Amplification Reaction for Readout of Receptor‐Mediated Cellular Forces

Mechanics play a fundamental role in cell biology, but detecting piconewton (pN) forces is challenging because of a lack of accessible and high throughput assays. A mechanically induced catalytic amplification reaction (MCR) for readout of receptor‐mediated forces in cells is described. Mechanically labile DNA duplexes presenting ligands are surface immobilized such that specific receptor forces denature the duplex and thus expose a blocked primer. Amplification of primers is achieved using an isothermal polymerization reaction and quantified by fluorescence readout. As a proof of concept, the assay was used to test the activity of a mechanomodulatory drug and integrin adhesion receptor antibodies. To the best of our knowledge, this is the first example of a catalytic reaction triggered in response to molecular piconewton forces. The MCR may transform the field of mechanobiology by providing a new facile tool to detect receptor specific mechanics with the convenience of the polymerase chain reaction (PCR).